用户工具

站点工具


5.0_inch_rpi_lcd-jrp5002

差别

这里会显示出您选择的修订版和当前版本之间的差别。

到此差别页面的链接

两侧同时换到之前的修订记录 前一修订版
后一修订版
前一修订版
5.0_inch_rpi_lcd-jrp5002 [2021/06/02 18:46]
xuwei
5.0_inch_rpi_lcd-jrp5002 [2021/10/19 11:00] (当前版本)
jlttek [FAQ]
行 1: 行 1:
 ====== 5.0 inch RPi LCD-JRP5002 ====== ====== 5.0 inch RPi LCD-JRP5002 ======
 ===== 产品图片 ===== ===== 产品图片 =====
-{{:lcd:JRP50021.jpg?300|}} +{{:5002-1.jpg?nolink&400 |}} 
-{{:lcd:JRP50022.jpg?300|}}+{{:5002-4.jpg?nolink&400|}} 
 +===== 产品介绍 ===== 
 +通用5英寸HDMI显示屏,分辨率为800×480,带有电容式触摸屏。它支持树莓派,也可以用作电脑显示器。 
 +===== 产品特征 ===== 
 +  * 全视角LCD显示屏 
 +  * 800×480硬件分辨率,可以通过软件配置分辨率(最高可支持1920×1080) 
 +  * 电容式触摸屏,最大支持5点触控 
 +  * 带背光按键(可关闭背光,降低功耗) 
 +  * 兼容Raspberry Pi、BB Black、Banana Pi等主流迷你PC 
 +  * 用作树莓派显示器,支持 Raspbian、Ubuntu、Kodi、Win10 IOT,无需驱动 
 +  * 也可作为通用HDMI显示器,连接电脑、电视盒、微软Xbox360、索尼PS4、任天堂Switch等 
 +  * 用作PC显示器,支持Win7,Win8,Win10系统5点触摸(XP和旧版本系统:单点触摸),免费驱动器 
 +  * 带3.5mm音频接口,支持HDMI音频输出
  
-===== Introduction ===== +===== 连接到树莓派使用 =====
-800x480, 5.0 inch Touch Screen TFT LCD Designed for Raspberry Pi/MiniPC/etc.HDMI. +
-===== Features ===== +
-  * Wide viewing angle LCD +
-  * 800x480 hardware resolution,maximum HDMI resolution 1920X1080 is supported +
-  * Capacitive touch screen, support 5 point touch maximum +
-  * With Mini HDMI interface +
-  * Built-in OSD menu adjustment function (adjustable Contrast/ Brightness/Saturation, etc.) +
-  * It is compatible with mainstream mini PC such as Raspberry Pi, BB Black, Banana Pi +
-  * Used as a Raspberry Pi display that supports Raspbian, Ubuntu, Kodi, Win10 IOT, single-touch, free drive +
-  * It can also be used as a general-purpose HDMI display, connecting computers, TV boxes, Microsoft Xbox360, SONY PS4, Nintendo Switch and so on +
-  * Work as a PC monitor, support Win7, Win8, Win10 system 5 point touch (XP and older version system: single-point touch), free drive +
-  * High quality immersion gold surface plating +
-  * Support HDMI audio output +
-===== Parameters ===== +
-^ Name                   | Parameter             | +
-| Screen Size            | 5.0(inch)             | +
-| SKU                    | JRP5002           | +
-| Display Color          | RGB 16.7M color         | +
-| Type                   | TFT.TN                | +
-| Driver IC              | --               | +
-| Resolution             | 800*480 (Pixel)       | +
-| Module Interface       | HDMI interface +
-| Outline Dimension      | 121.01*78.13 mm       | +
-| Active Area Dimension  | 108*64.08 mm        | +
-| VCC power voltage      | 5.0V              | +
-| Power Consumption      | 560mA@5.0V             | +
-| Weight(No packaging)                         | +
-===== Use with Raspberry Pi ===== +
-==== Install image ==== +
-  - Download the latest image from the official  +
-  - Install the system according to the official tutorial steps +
-==== Modify the “config.txt” ==== +
-After the programming of Step1 is completed, open the config.txt file of TF card root directory and +
-add the following code at the end of the file, save and eject Micro SD Card safely: +
-      hdmi_force_edid_audio=1 +
-      max_usb_current=1 +
-      hdmi_force_hotplug=1 +
-      config_hdmi_boost=7 +
-      hdmi_group=2 +
-      hdmi_mode=1 +
-      hdmi_mode=87 +
-      hdmi_drive=1 +
-      hdmi_cvt 800 480 60 6 0 0 0 +
-==== Drive Pi ==== +
-Insert the TF Card to Raspberry Pi, connect the Raspberry Pi and LCD by HDMI cable; connect USB cable to one of the four USB ports of Raspberry Pi, +
-and connect the other end of the USB cable to the USB port of the LCD; then supply power to Raspberry Pi; +
-after that if the display and touch both are OK, it means drive successfully (please use the full 2A for power supply). +
-===== Use as PC monitor ===== +
-  - Connect the computer HDMI output signal to the LCD HDMI interface by using the HDMI cable +
-  - Connect the LCD's USB Touch interface (Either of the two MicroUSB) to the USB port of the device +
-  - If there are several monitors, please unplug other monitor connectors first, and use LCD as the only monitor for testing +
-===== Rotate the display direction ===== +
-<color #ed1c24>This method only applies to the Raspberry Pi series of display screens, other display screens do not apply</color>+
  
-**Method 1,**If the driver is not installed, execute the following command (Raspberry Pi needs to connected to the Internet): +用于树莓派的 Raspbian Ubuntu Kali Retropie 和 WIN10 IoT 系统。
-    sudo rm -rf LCD-show +
-    git clone https://github.com/lcdgogo/LCD-show.git +
-    chmod -R 755 LCD-show +
-    cd LCD-show/ +
-    sudo ./XXX-show 90 +
-     +
-After execution, the driver will be installed. The system will automatically restart, and the display screen will rotate 90 degrees to display and touch normally. +
-( <color #ff7f27>' XXX-show '</color> can be changed to the corresponding driver, and <color #ffaec9>' 90 '</color> can be changed to 0, 90, 180 and 270, respectively representing rotation angles of 0 degrees, 90 degrees, 180 degrees, 270 degrees)+
  
-**Method 2**If the driver is already installed, execute the following command: +//当LCD在Raspberry Pi系统上运行时必须手动设置分辨率,否则会导致显示异常。当LCD在Windows系统的PC版本上工作时,没有这种问题//
-    cd LCD-show/ +
-    sudo ./rotate.sh 90 +
-     +
-After execution, the system will automatically restart, and the display screen will rotate 90 degrees to display and touch normally. +
-( <color #ff7f27>' 90 '</color> can be changed to 0, 90, 180 and 270, respectively representing rotation angles of 0 degrees, 90 degrees, 180 degrees, 270 degrees)+
  
-<color #ed1c24>If the rotate.sh prompt cannot be found, use Method to install the latest drivers</color> + 请在[[https://www.raspberrypi.org/software|Raspberry Pi]]官方网站上下载该图像的最新版本。  
-===== Resources ===== + 
-==== User Manual ====+(1).将压缩文件下载到PC并解压缩以获取.img文件。 
 + 
 +(2).将TF卡连接到PC,使用[[http://www.lcdgogo.com/tools/PanasonicSDFormatter_ha.rar|SDFormatter.exe]] 软件格式化TF卡。 
 + 
 +(3).打开[[http://www.lcdgogo.com/tools/Win32DiskImager.rar|Win32DiskImager.exe]]软件,选择在步骤1中准备的系统映像,然后单击“写入”以刻录系统映像。   
 + 
 +(4).编程完成后,打开TF卡根目录下的config.txt文件,注释掉dtoverlay=vc4-fkms-V3D。 
 + 
 +(5).并在config.txt的末尾添加如下代码,保存并安全弹出TF卡。 
 +  max_usb_current=1 
 +  hdmi_group=2 
 +  hdmi_mode=87 
 +  hdmi_cvt 800 480 60 6 0 0 0 
 +必须确保等号两边没有空格。 
 + 
 +//注意:如果是树莓派4,还需要注释掉**dtoverlay=vc4-fkms-V3D**。//    
 + 
 +1).保存TF卡并将其插入Raspberry Pi中。 
 + 
 +2).将LCD的Touch接口连接到树莓派的USB接口。 
 + 
 +3)..将液晶显示器的HDMI接口连接到树莓派的HDMI接口,给树莓派上电,等待几秒即可正常显示。 
 +   
 +   
 +   
 +   
 +   
 +   
 +   
 + 
 + 
 +===== 连接到PC机使用 ===== 
 + 
 +用于PC的Windows系统。此液晶显示器可在 PC 版本 Windows 7/8 / 8.1 / 10 系统上工作。方法如下:   
 + 
 +1) 将 LCD 的 TOUCH 接口连接到 PC 的 USB 接口。一段时间后,Windows 将自动识别触摸功能。   
 +   
 +2) 如果使用HDMI通讯,将LCD的HDMI接口连接到PC的HDMI接口。大约 5 秒后,您可以正常看到 LCD 显示。如果需要输出声音,可以通过HP音频输出连接到3.5毫米耳机。   
 +   
 +//**注意:**//  
 + 
 +//1) 当PC同时连接到多个显示器时,只能使用LCD来控制主显示器上的光标。因此,建议将 LCD 设置为主显示。// 
 + 
 +//2) 部分PC不支持即插即用的HDMI设备。一般重启系统后即可正常使用。// 
 + 
 +//3) 部分PC可能会因为USB接口供电不足导致LCD闪烁。通常,它们通过DC接口连接到外部5V / 2A电源后即可正常使用。// 
 + 
 +//4) HP音频输出只能在HDMI通信期间正常使用。// 
 +===== 旋转显示方向 ===== 
 + 
 +=== 显示旋转 ===  
 + 
 +1.在config.txt文件中添加一条语句(该配置文件位于TF卡的根目录中,即/ boot): 
 +  display_rotate=1  
 +//**注意:1=90°;2=180°; 3=270°**// 
 + 
 +//**注意: 如果是树莓派4,还需要注释掉dtoverlay=vc4-fkms-V3D。**// 
 + 
 +2.保存后重新启动Raspberry Pi 
 +  sudo reboot 
 + 
 +=== 触摸旋转 ===  
 + 
 +旋转显示器后,触摸位置不正确,因为触摸不会随显示角度变化。所以触摸需要修改。 
 + 
 +1. 安装libinput 
 +  sudo apt-get install xserver-xorg-input-libinput 
 +如果要安装Ubuntu系统或Jetson Nano。安装说明是: 
 +  sudo apt install xserver-xorg-input-synaptics 
 +2. 在/etc/X11/下创建xorg.conf.d目录(如果目录已经存在,直接进行步骤3) 
 +  sudo mkdir /etc/X11/xorg.conf.d 
 +3. 将40-libinput-conf文件复制到刚刚创建的目录中 
 +  sudo cp /usr/share/X11/xorg.conf.d/40-libinput.conf /etc/X11/xorg.conf.d/ 
 +4. 编辑文件 
 +  sudo nano /etc/X11/xorg.conf.d/40-libinput.conf  
 +找到触摸屏的一部分,在其中添加以下语句,然后保存 
 +  Option "CalibrationMatrix" "0 1 0 -1 0 1 0 0 1" 
 +{{ :touch_roate.jpg?nolink |}} 
 +5. 重新启动Raspberry Pi 
 +  sudo reboot 
 + 
 +完成上述步骤后,您可以执行90度旋转。 
 + 
 +//注意:// 
 + 
 +//90 度旋转: **Option "CalibrationMatrix" "0 1 0 -1 0 1 0 0 1"**// 
 + 
 +//180 度旋转: **Option "CalibrationMatrix" "-1 0 1 0 -1 1 0 0 1"**// 
 + 
 +//270 度旋转: **Option "CalibrationMatrix" "0 -1 1 1 0 0 0 0 1"**// 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 + 
 +===== 资源 ===== 
 +==== 用户手册 ====
 [[http://www.lcdgogo.com/LCDspc/JRP5002-PSS.pdf|JRP5002-PSS.pdf]] [[http://www.lcdgogo.com/LCDspc/JRP5002-PSS.pdf|JRP5002-PSS.pdf]]
  
-==== install_matchbox-keyboard ====+==== install_matchbox-键盘 ====
 [[http://www.lcdgogo.com/tools/How_to_install_matchbox-keyboard(En).pdf|How_to_install_matchbox-keyboard.pdf]] [[http://www.lcdgogo.com/tools/How_to_install_matchbox-keyboard(En).pdf|How_to_install_matchbox-keyboard.pdf]]
  
-==== Image ==== +==== 镜像文件 ==== 
-System Name                       ^ System Version   | Supported Raspberry Pi version     | Default user and passwd         | Download                                                                                                         +<color #ed1c24>注意:JRP5002可通用JRP5008的镜像,资源如下: 
-| Raspbian                          2019-09-26       | PI4/PI3B+/PI3/PI2/PI1/ZERO/ZERO W  | user: pi\\ password: raspberry  | [[https://pan.baidu.com/s/1CsGRtxGD_w8aKIgzJHxZ1A|MPI5001-5inch-B-raspbian-buster-2019-09-26]]  Fetch code:w08y  +</color> 
-Ubuntu-mate                       18.04.2-beta1    | PI3B+,PI3,PI2                      | user: pi\\ password: raspberry  | [[https://pan.baidu.com/s/14sJ1vlQwlB8_37MCnJBrEg|5inchB-800X480-RPI3-RPI2-ubuntu-mate-16.04-beta2]] Fetch code:szc8      | +System Name                   | System Version  | Supported Raspberry Pi version     | Default user and passwd          Download                                                                                                                               |
-| Kali Linux RaspberryPi 2,3 and 4  2019.4           | PI4B,PI3B+,PI3,PI2                 | user: root\\ password: toor     | [[https://pan.baidu.com/s/1nCAL7RtMkNi35uOIrsHbeg|MPI5001-5inch-B-800x480-Kali-2019.4]] Fetch code:tpbs                  |+| Raspbian                      2021.03.04      | PI4/PI3B+/PI3/PI2/PI1/ZERO/ZERO W  | user: pi\\ password: raspberry  | Baiduyun:  | [[https://pan.baidu.com/s/1PDeJ1_aH3Xgs8RoSGr1jUg|JRP5008-5inch-B-2021-03-04-raspios-buster-armhf]]  Fetch code:wij2       
 +:::                           :::             | :::                                | :::                             | mega:      | [[https://mega.nz/folder/f3xgDDhQ#N9A7Kxmyt_CTxt-30sleTA|JRP5008-5inch-B-2021-03-04-raspios-buster-armhf]]                  | 
 +| Ubuntu-MATE-32bit             | 1905/7/12       | PI4,PI3B+,PI3,PI2                  | user: pi\\ password: raspberry  | Baiduyun:  | [[https://pan.baidu.com/s/1IVPZPCJUyTcXvr1jXMpA_A|JRP5008-5inch-B-ubuntu-mate-20.10-desktop-armhf+raspi]] Fetch code:fk1r  | 
 +| :::                           | :::             | :::                                | :::                             | mega:      | [[https://mega.nz/folder/ai4AVDgT#6wIME124jY6YmXNk0aQqsw|JRP5008-5inch-B-ubuntu-mate-20.10-desktop-armhf+raspi]]            
 +| Kali Linux RaspberryPi-32bit  2020.4          | PI4B,PI3B+,PI3,PI2                 | user: kali\\ password: kali     | Baiduyun:  | [[https://pan.baidu.com/s/1nvoDbsuWDPoOxX5vQnUQiA|JRP5008-5inch-B-kali-linux-2020.4-rpi4-nexmon]] Fetch code:ho7v          | 
 +| :::                           | :::             | :::                                | :::                             | mega:      | [[https://mega.nz/folder/Lr5AFBJB#RngHWR7uLZCBY8fL4T03qQ|JRP5008-5inch-B-kali-linux-2020.4-rpi4-nexmon]]                    | 
  
-==== Driver ==== 
-[[http://www.lcdgogo.com/lcddriver/LCD-show.tar|LCD-show.tar]] 
 ==== Software==== ==== Software====
   * [[http://www.lcdgogo.com/tools/PanasonicSDFormatter_ha.rar|PanasonicSDFormatter_ha]]   * [[http://www.lcdgogo.com/tools/PanasonicSDFormatter_ha.rar|PanasonicSDFormatter_ha]]
行 97: 行 156:
   * [[http://www.lcdgogo.com/tools/Putty.zip|Putty]]   * [[http://www.lcdgogo.com/tools/Putty.zip|Putty]]
 ===== FAQ ===== ===== FAQ =====
-====How to install drivers Online==== +1.树莓派黑边问题
-**Step 1. Install Raspbian official image**  +
-  - Download the latest Raspbian Image from the official website: https://www.raspberrypi.org/downloads/ +
-  - Format TF card by SDFormatter +
-  -  Burn the official image into TF card by using Win32DiskImager +
-**Step 2. obtain the LCD driver**  +
-Log onto the Raspberry Pi users system to command line (The initial user name: pi Password: +
-raspberry) +
- +
-Get the newest driver from GitHub(Raspberry Pi LCD should be connected to internet) +
-    sudo rm -rf LCD-show +
-    git clone https://github.com/lcdgogo/LCD-show.git +
-    chmod -R 755 LCD-show +
-    cd LCD-show/ +
-**Step 3. install LCD driver** +
-    sudo ./LCD5-show +
-     +
-Wait for a moment after executing the above command, then you can use the corresponding raspberry +
-LCD. +
-====How to install drivers Offline==== +
- +
-**Step 1. Install Raspbian official image**  +
-  - Download the latest Raspbian Image from the official website: https://www.raspberrypi.org/downloads/ +
-  - Format TF card by SDFormatter +
-  -  Burn the official image into TF card by using Win32DiskImager +
-**Step 2. obtain the LCD driver**  +
-Download from the following address: +
-[[https://github.com/lcdgogo/LCD-show|https://github.com/lcdgogo/LCD-show]] +
- +
-Copy the LCD-show.tar.gz drive to the Raspberry Pi system root directory (Suggestion: +
-copy flash driver directly to TF card after completion of Step 1, or copy by SFTP or other +
-methods for remote copy). Unzip and extract drive files as the following command: +
- +
-    cd /boot +
-    sudo tar zxvf LCD-show.tar.gz +
-    cd LCD-show/ +
-     +
-**Step 3. install LCD driver** +
-The same as method1-Setp3.+
  
 +  sudo nano /boot/config.txt
  
 +把前面#去了,后面的值改成负的,默认是16
  
 +  overscan_left=-28
 +  overscan_right=-30
 +  overscan_top=-30
 +  overscan_bottom=-30
 ===== Support ===== ===== Support =====
  
5.0_inch_rpi_lcd-jrp5002.1622630812.txt.gz · 最后更改: 2021/06/02 18:46 由 xuwei